| With illumination and
targeting systems getting smaller, lighter and more compact, we're moving
with the industry, law enforcement and the military to reflect that change
in these products. |
|
|
The Patent Pending
MOD-C is a superior, light weight clamp (weighs only 1.6oz)
is small and compact enough to reduce your shotgun profile so
it reduces hang ups and snags. Spaced between the barrel and magazine tube
it will not block your peripheral sight picture. Manufactured from aluminum
and hard coat anodized, it will not crack or break no matter how hard you
tighten it down. One tool for one bolt is all that is needed to attach and
remove this clamp in seconds. A steel threaded insert assures you won't strip
a thread. Includes 3M polyurethane no slip grip to protect your finish. |
|
The BMT clamp is lighter
than the factory Remington stamped steel clamp that comes on the Remington
870 with an extended magazine tube. You can mount a variety of rails and
sling mount systems on this clamp. This clamp holds the light between the
barrel and magazine tube for fingertip actuation of lights on either the
left or right side of the shotgun without blocking your periferal sight picture.
It can use 6 slot or 3 slot rails to put the light and clamp exactly where
you need it.One tool for one bolt is all that is needed to attach and remove
this clamp in seconds. Includes 3M polyurethane no slip grip to protect your
finish. |
|
The MTC is the latest
offering in the MT series of clamps for 1" lights. This clamp fits in a 1/2"
of space so it is perfect for the Mossberg 590A1 and just about any other
shotgun with a 1" magazine tube and room to mount it. This mount can be
positioned 3 ways, left, right, or below the shotgun and provides a solid
"lock up" around the mag tube. Each position allows for a sling to
be used with the included sling mount. Manufacturered from aircraft grade
aluminum and hard coat anodized it is a superior mounting solution for those
with limited space or under the gun mounting requirements. One tool for one
bolt is all that is needed to attach and remove the clamp or light in
seconds. |
Picture Coming Soon. |
The MTR is the latest
offering in the MT series of clamps for lights with built in attachment points.
This clamp fits in a 1/2" of space so it is perfect for the Mossberg 590A1
and just about any other shotgun with a 1" magazine tube and room to mount
it. This mount can be positioned 3 ways, left, right, or below the shotgun
and provides a solid "lock up" around the mag tube. Each position allows
for a sling to be used with the included sling mount. Manufacturered from
aircraft grade aluminum and hard coat anodized it is a superior mounting
solution for those with limited space or under the gun mounting requirements.
One tool for one bolt is all that is needed to attach and remove the clamp
or light in seconds. |
 |
You wouldn't put anything
metal against the side of your car would you? Of course not so why put metal
against your weapon? Stop scratches and sliding with these 3M polyurethane
protectant pads. Transparent protection from -49 to +200 degrees. You
can feel it grip before you even tighten the clamp.These are the same pads
used on CDM Gear clamps and are now available in a cut to fit design for
ATI, Choate, Mesa Tactical, Nordic and other clamps. |
COMING SOON |
The NEW CDM Gear A-Bar, short
for Accessory Bar, comes as a kit that includes an interchangeable breacher
cap and the bayonet cap. This replaces your barrel lug nut and offers a multitude
of new options for your Mossberg 500 especially if you have a Heat shield
you want to keep. The A-Bar accepts CDM Gear light mounts. The bayonet cap
can be used with a S&J Hardware bayonet receiver clamp at the rear to
mount a bayonet on your Mossberg 500 but the heat shield will have to be
removed for now. Made from aircraft quality aluminum and hard anodized they
have knurled sections for easy installation and removal. |
