The
CDM Gear ROC-12 series of light mounts is a US made railed barrel clamp that
is used to support factory and aftermarket 1" diameter magazine tubes, and
extensions, while providing low profile mounting rails on the left and right
side for rail mountable lights and acessories.
The
rail and clamp half are manufactured as one piece from aluminum and precision
CNC machined to size. All threaded holes are press formed into the mount
for hardness. The entire mount is then machine finished to soften round edges
before we type III mil spec hard coat anodized for durability. Fingers at
the top of the clamp allow for use with a barrel rib and/or compensation
ports, as well as slight barrel taper, while a solid surface on the bottom
accepts our 3M no slip grip pads to reduce movement under recoil.
Just
2 socket head cap screws work opposite each other to hold the clamp in place
and are included along with a wrench and our 3M no slip grip pads for the
magazine tube. The mount requires 1 1/2" of mounting surface without interference
from a heat shield. Will not work with heavy walled barrels or magazine tubes
larger than 1".
 |
The CDM Gear
ROC-12 is our base barrel clamp that is used to support factory and
aftermarket 1" diameter magazine tubes, and extensions, while providing mounting
rails on the left and right side for rail mountable lights and acessories.
All wrenches, screws and 2 anti slip pads are
supplied.
Fits Remington 870, 1100, 1187, Benelli
M1/M2/M4/M104, Mossberg 500 7 shot, 590, Winchester 1200, 1300, SXP. Fits
12 ga. shotguns with 1.25" of space on a 1" magazine tube. Will not work
on Benelli M3, SuperNova, Mossberg 590A1 or 930 SPX. |
ROC-12
MSRP $39.95 |
|
 |
The CDM Gear
ROC-12S is the same as above only it includes a limited rotation docking
point for a PBQD sling swivel. (sling swivel not included). All wrenches,
screws and 2 anti slip pads are supplied.
Fits Remington 870, 1100, 1187, Benelli
M1/M2/M4/M104, Mossberg 500 7 shot, 590, Winchester 1200, 1300, SXP. Fits
12 ga. shotguns with 1.25" of space on a 1" magazine tube. Will not work
on Benelli M3, SuperNova, Mossberg 590A1 or 930 SPX. |
ROC-12S
MSRP $45.95 |
 |
 |
The CDM Gear
ROC-12R is the same as the ROC-12 only the ROC-12R uses our patented
ring and curved rail design, using a flashlight ring mount (included) to
draw tight a 1" round bodied tac light into the curved portion of the rail
to locate the light. This mount gives you the choice of using either a round
bodied tac light or a rail mountable light/laser, or both! All wrenches,
screws and 2 anti slip pads are supplied.
Fits Remington 870, 1100, 1187, Benelli
M1/M2/M4/M104, Mossberg 500 7 shot, 590, Winchester 1200, 1300, SXP. Fits
12 ga. shotguns with 1.25" of space on a 1" magazine tube. Will not work
on Benelli M3, SuperNova, Mossberg 590A1 or 930 SPX. |
ROC-12R
MSRP $49.95 |
|
 |
The MTRS fits
in the small space of the Mossberg 590 SHOCKWAVE. This mount can be positioned
2 ways, left, or right, and provides a solid "lock up" around the mag tube
that stays in place when you remove the barrel. Sling loops side and botom.
Manufacturered from aircraft grade aluminum and hard coat anodized it is
a superior mounting solution for those with limited space. One tool for one
bolt is all that is needed to attach and remove the clamp. May not fit wood
furnature models. |
MTRS
MSRP $39.95 |
|
 |
The MTR fits
in the small space of the Mossberg 590 A1 and Mossberg 500. This mount can
be positioned 2 ways, left, or right, and provides a solid "lock up" around
the mag tube that stays in place when you remove the barrel. Sling loops
side and botom. Manufacturered from aircraft grade aluminum and hard coat
anodized it is a superior mounting solution for those with limited space.
One tool for one bolt is all that is needed to attach and remove the
clamp. |
MTR
MSRP $39.95 |
|
 |
The MTRS-20 fits
in the small space of the Mossberg 590 SHOCKWAVE 20 gauge. This mount can
be positioned 2 ways, left, or right, and provides a solid "lock up" around
the mag tube that stays in place when you remove the barrel. Sling loops
side and botom. Manufacturered from aircraft grade aluminum and hard coat
anodized it is a superior mounting solution for those with limited space.
One tool for one bolt is all that is needed to attach and remove the clamp.
May not fit wood furnature models. |
MTRS-20
$39.95
|
|
 |
The MTRS-U12
fits in the small space of the Mossberg 590 SHOCKWAVE 12 gauge and gives
you a poisition to mount a light under the shotgun. This mount can be positioned
left, or right, and provides a solid "lock up" around the mag tube that stays
in place when you remove the barrel. Manufacturered from aircraft grade aluminum
and hard coat anodized it is a superior mounting solution for those with
limited space. One tool for one bolt is all that is needed to attach and
remove the clamp. May not fit wood furnature models. |
MTRS-U12
MSRP $39.95 |
|
 |
The G8TR M-LOK®
Light Mount is a Zero Profile, forward position light mount using our patented
ring in rail design. It allows you to use a round bodied 1" tactical light
or a rail mounted light. It is designed to be less complicated to create
as low a profile as possible . This M-LOK® system comes with all hardware
and wrenches. This mount can not be fully used on MOE® forends due
to the front lip. Please see the G8TR-C
for MOE® forends. |
G8TR
Lightmount
MSRP $39.95 |
|
 |
The G8TR -C
M-LOK® Light Mount for MOE® forends and handguards
is a cantilever light mount using our patented ring in rail design alowing
you to use a round bodied 1" tactical light or a rail mounted light. It is
designed to be less complicated to create as low a profile as possible in
a cantilever package. This M-LOK® system comes with all hardware and
wrenches. |
G8TR-C
Lightmount
MSRP $39.95 |
|
|
|